技術中心
技術中心
當前位置: 首頁 -> 產品中心
Gewiss自復位斷路器電路測試Restart ELECTRIC CIRCUIT TEST
All the RESTART range is equipped with an integrated electronic circuit which can test system condition and allows the resetting of circuit breaker if the measured values are compatible with presetting safety values. During the electric circuit test, RESTART injects into the downstream electrical system a pulsating unidirectional current in order to check its condition. The test current intensity is extremely low, so the safety of people is guaranteed in all circumstances.
所有的RESTART產品內部都有一個集成電路用于系統測試,并且在當測試值滿足預設的安全值時使斷路器復位。在進行電路測試期間,RESTART產生一個單向脈沖電流注入到下游電路中,這個測試電流的強度非常小,在任何情況下都可以保證人員的安全。
RESTARTRM, besides checks earth insulation resistance, also tests the electrical system for short circuit. The device measures the impedance between two active conductors and if the value is equal to or less than 1 Ω, the reset will not carried out.
RESTARTRM除了檢測線路對地的絕緣電阻外,也對系統是否存在短路情況進行檢測。RESTARTRM測量兩個有效導體之間的電阻,如果這個電阻在1Ω之內則不對斷路器進行復位操作。
All devices can detect faults also for electrical systems without earthing.
所有的設備都可以檢測漏電,即使在系統沒有接地的情況下。
The table shows the different reset and block (or standby) values that the different versions of RESTART use as a reference, by comparing them to electrical system measured values.
|
RESTART Type |
IΔn |
絕緣檢測 |
短路檢測 | ||
|
復位值RD |
阻斷值RD0 |
復位值RD |
阻斷值RD0 | ||
|
RESTART with AUTOTEST 2P
RESTART RD2P |
30 mA |
400 (70*) kΩ |
120 (20*) kΩ |
- |
- |
|
RESTART RM 2P |
30 mA |
400 (70*) kΩ |
120 (20*) kΩ |
1 Ω |
1 Ω |
|
RESTART with AUTOTEST PRO 4P RESTART RD 2P/4P |
30-100 mA |
16 kΩ |
8 kΩ |
- |
- |
|
RESTART with AUTOTEST PRO 4P RESTART RD 2P/4P |
300-500 mA |
5 kΩ |
2.5 kΩ |
- |
- |
|
RESTART RM PRO 2P / 4P |
30 mA |
16 kΩ |
8 kΩ |
1 Ω |
1 Ω |
|
RESTART RM PRO 2P / 4P |
300 mA |
5 kΩ |
2.5 kΩ |
1 Ω |
1 Ω |







